Pond Sealant
Soilfloc® Sealant is the best polymer based sealant available for your canal, irrigation ditch or watering hole. Specifically designed to find leaks, whether in the floor, the wall or through rock formations and seal them.

Muck Remover
The biological removal of muck and sludge from ponds, lakes and canals is an ecological way to eliminate organic sediments from ruining shorelines and making swimming impossible.

Dock Bubblers
Bubbler systems use perforated tubing placed at the bottom of the water around a boathouse, dock or wall.

Solar Aeration

Bacteria & Clarifiers

Ponds Aeration

Pond Books & Guides
Our Selected Books On Amazon
As an Amazon affiliate we may recieve payment for purchases made through Amazon.


Lake and Pond
Management Guidebook




Earth Ponds
Pond Maker's Guide



Information & Articles

Best diffuser for aerating wastewater tank with high BOD?

Hi,
 
I recently purchased a rotary vane compressor (GAST AT05 Rotary Vane) and I am trying to figure out what type and how many diffusers I should use with it. Here are the motor specs:
 
1/4HP, 60Hz, 115V,
Phase 1, 1725 RPM, 4.7A, 1.00SF
10 PSI Max. Pressure Continuous Duty
4.8 CFM Open Flow
Marathon Motor

 
We are using it to treat brewery wastewater (high in BOD's). We will most likely encounter some sludge formation on the bottom of our treatment pit. Anything that is clog resistant would be better.

It is about 6 feet deep. We have three chambers in the basin. The one we are using first is 10'x10'. I will know more about flow rates in the coming days. We are brewing our second batch tomorrow. I am assuming we will need to treat 1000 - 5000 gallons?

Thanks for your help.

 
asked by anonymous
edited

Please log in or register to answer this question.

1 Answer

0 votes

Hello,

The pump has a fairly low output at only 4.8 CFM but since the basin is only 10' x 10' you could get four or more airstones into the tank, with one cfm flow for each diffuser. A small or fine bubble system would be best and with the sludge in the basin you would want something that can be cleaned fairly easily as with any diffuser there will be issues of clogging in such a situation.

Probably the best bet, and less expensive, would be fine bubble stones. You could run 3 to 6 of these airstones with your pump. They can be cleaned with muriatic acid when they start getting fouled up. It's a good cheap option: http://www.thepondreport.com/store/diffusers-airstones/airstones-diffusers

Whatever way you go you should use a 1/2" or 5/8" feeder line from your pump manifold to each diffuser to reduce back pressure although with a shallow tank like that it won't make much of an issue.. If suspended solids are an issue you might need to put the diffuser in a weighted pail so it isn't touching the bottom.

We do have some weighted asssemblies with the same airstones attached to reduce any stirring of sediments but for a low-cost solution just put the airstone into a small plastic pail with a few stones to weigh it down.



 

answered by TPR

Pond Report Store

Algaecides & Bacteria | Deicers & Bubblers | Weed Removal | Liquid Bacteria | Pond Pumps & Fountains | Aeration | Winter Pond Care | Algae Control | Pond Liner | Muck Pellets | Build a Solar Aerator | Rotary Vane Compressors | Floating Fountains | Building a Pond | Linear Air Compressors & Pumps | Weighted Airline | Diffusers & Airstones | Solar Aeration Systems | DC & Battery Operated Pumps | Windmill Aeration | Dock Bubbler Packages | Building a Waterfall | Dyes & Colorants | Consultations | Questions & Answers | Links & Resources | Eurasian Milfoil | |
Mosquito Control | Pondkeeper Treatments | Aeration Systems | Septic Bacteria | Grease Trap Blocks | Dissolved Oxygen Meters | SOTR & Pumping Rates | Duckweed Control | Pond Plans & Pond Building Books & Guides

Contact Us

© 2007 - 2024 The Pond Report

...